seal cover
英 [siːl ˈkʌvə(r)]
美 [siːl ˈkʌvər]
网络 密封罩
双语例句
- A seal is provided between the flexible body and the pot cover.
弹性体与锅盖之间设置有密封件。 - Improvement for the mechanical seal cover and nationalized modification for the mechanical seal are made, and good results and benefit have been achieved.
分析了引进苯酐泵的运行情况，进行了机封压盖改进和机封国产化设计，取得了良好的效果和效益。 - To seal the camshaft housing cover, use only the approved sealant from the Porsche parts catalog!
若要密封凸轮轴室盖，请使用“porsche汽车零件目录”中批准的密封剂！ - Reliability analysis of composite seal cover based on transient dynamics
基于瞬态动力学的复合材料密封盖可靠性分析 - A pop-top seal cover is composed of a mounting with a rib, an upper cover, a sealing gasket, a central axis and a handle.
易拉罐密封盖由带有凸棱的底托。上盖。密封垫。中轴和把柄五部分组成。 - Bolted cover plate to protect seal and cylinder from the ingress of debris. He opened the cover in which the message was enclosed.
上盖板可防止杂物进入缸筒损坏密封。他把密封那份电报的封套拆开。 - A motor shaft gap used for a sealing plate for a seal air channel is left between the belt pulley and the end cover of the motor shell.
在皮带轮同电机机壳端盖之间保留供密封风道用的密封板穿过的电机轴空隙位。 - A mechanical seal and water seal combined floor drain consists of a floor drain cover, a main floor drain body, a float and a hose type magnetic seal valve.
一种机械密封与水封组合地漏，由地漏盖、地漏主体、浮子和软管式磁力密封阀组成。 - Technique issues such as clamping deformation, guarantee of hole position accuracy and plane seal, etc. for motorcycle case body and case cover are introduced.
介绍了摩托车箱体、盖加工中的装夹变形、位置精度和平面密封保证等方面的工艺问题。 - The utility model discloses an instantaneous cleaning envelope for postal articles, composed of a cover, a seal lip and a cover lip.
本实用新型公开了一种邮政邮品及时洁信封，它由封套、封舌和盖舌组成。 - Moreover, the obturating ring can reliably seal the cylinder and the end cover.
且密封圈能将筒体和端盖可靠的密封。 - Insert Timing Case Cover Alignment and Seal Installation Tool 6139 in the crankshaft opening in the cover.
在曲轴盖的开口处，插入正时箱盖定位和轴封安装工具6139。 - Replace the oil seal in the timing case cover.
更换在正时箱盖中的油封。 - Therefore, when the mechanical seal leakage test run to exclude inter-shaft seal and cover basically are due to dynamic and static friction ring caused by the destruction.
因此，试运转机会械密封泄漏在消除轴间及端盖密封失效后，基础上都是由于动、静环摩擦副受损坏所致。 - I broke the seal and read. He opened the cover in which the message was enclosed.
我撕开封口，开始念信。他把密封那份电报的封套拆开。 - An Application of the Bipyramid Balance Seal Cover in the Acid-containing Trailer
双锥平衡密封盖在装酸槽车上的应用 - Formation Process and Die of Bearing Seal up Cover
滚动轴承座密封罩成形工艺及模具 - The vitrification rate caused by cotton plug wrapped in cheese cloth was the lowest among all seal materials, including polyethylene film, plastic cover and sulfuric paper.
封口材料中聚乙烯膜和塑料瓶盖两个处理玻璃化率相似且玻璃化率高，硫酸纸次之，棉塞的最低。 - The paper analyses the difficulty of bearing seal up cover stamping process and deals with the effective process measures and the key points of die designing.
分析了密封罩零件冲压成形的难点，论述了采取的有效工艺措施和模具设计要点。 - A New Method of Seal Bottom of Underground Structure without Draining Off Water-No Cover Hoist Bucket
地下构筑物不排水封底的新方法&开口吊罐施工法 - Improvement design of DF_4 locomotive hydraulic motor oil seal cover
DF4型机车静液压马达油封盖的改进方案 - Improvement of the seal structure of head cover flange of primary waste heat boiler
第一废热锅炉顶法兰密封结构改进 - During operation, the seal of cover found always broken, Created Seal to lose efficacy and influence on normal work of preheater.
在使用中其底益密封经常发现垫子破损，造成密封失效，严重影响预热器的正常工作。 - The PLC Control System of Large Hydraulic Press for Boiler Seal Cover
大型锅炉封头油压机的PLC程序控制系统 - After extensive analytical work, a significant conclusion can be arrived at that the finger seal assembled with aft cover plate of smaller bore diameter has better synthetical characteristics of low hysteresis and stiffness.
从综合影响角度考虑，具有较小后遮流板内径的指尖密封体现出更为优良的低迟滞和低刚度的综合特性。 - By utilizing the space between hydraulic motor oil seal cover and cooling fan core wheel end surface reasonably and improving the structure, these troubles have been eliminated efficiently.
通过合理利用静液压马达油封盖与冷却风扇轮心端面间的空间，进行加装和改进，有效地防止了马达油封的漏泄。 - Measures for equalizing the axial force are offered: ( 1) enlarging the back seal ring to produce a upward axial force on the front cover plate;
提出了平衡轴向力的2项具体措施：（1）加大后密封环的尺寸，使部分后密封环对应的前盖板受到向上的轴向力； - Mechanism Analysis and Parameter Design of Rolling Seal Mechanism for Twisting Breakable Cover
扭断盖滚压封口机的机构分析与参数设计 - Through simulation experiments, to achieve the seal cover containing the watermark information in the Word document.
通过仿真实验，实现将含有水印信息的印章盖在Word文档上。